Net Tractor Talk
       

Go Back   Net Tractor Talk > Search Forums

Showing results 1 to 16 of 16
Search took 0.01 seconds.
Search: Posts Made By: jdgreen
Forum: John Deere Forum 12-30-2017, 09:05 PM
Replies: 4
Views: 1,053
Posted By jdgreen
SOunds like you have a problem in the...

SOunds like you have a problem in the differential or rear final drive. Have you tried to engage differential lock to see if rear wheels will drive? Also, is it a 410, or a 410a, b, c, or d or ...?
Forum: John Deere Forum 03-26-2017, 08:15 PM
Replies: 1
Views: 3,103
Posted By jdgreen
THe filter and screen could be a problem and is a...

THe filter and screen could be a problem and is a good place to start. If other hydraulic functions are working OK, I doubt that will fix it though. Sounds like you have low pressure to the clutch or...
Forum: John Deere Forum 01-06-2017, 04:52 PM
Replies: 2
Views: 3,112
Posted By jdgreen
WHat is bad about the 4630 transmission? It...

WHat is bad about the 4630 transmission? It should be able to be rebuilt although it can get very expensive.
Forum: John Deere Forum 01-06-2017, 04:49 PM
Replies: 2
Views: 3,112
Posted By jdgreen
Unfortunately the 4630 is a larger framed...

Unfortunately the 4630 is a larger framed tractor. The 4430 transmission will not bolt up and I don't think any of the gears inside are the same either.
Forum: John Deere Forum 06-03-2016, 08:48 PM
Replies: 3
Views: 3,593
Posted By jdgreen
Springs typically do not need replacement. The...

Springs typically do not need replacement. The detent roller many times is worn and needs replacement. Sometimes the detent cam also...
Forum: John Deere Forum 05-31-2016, 09:13 PM
Replies: 3
Views: 3,593
Posted By jdgreen
I have adjusted hundreds of these over the years,...

I have adjusted hundreds of these over the years, but I have always used the special tools and dial indicator to adjust the valves. The 2 return valves get adjusted to about .021" clearance and the...
Forum: John Deere Forum 03-23-2016, 09:45 PM
Replies: 2
Views: 2,992
Posted By jdgreen
The diagram is not very good quality but you get...

The diagram is not very good quality but you get the idea. It is one choice of 4 possible distributors for the 1010.
Forum: John Deere Forum 02-11-2016, 08:56 PM
Replies: 1
Views: 2,680
Posted By jdgreen
Just coil up the extra and tie it up neatly.

Just coil up the extra and tie it up neatly.
Forum: John Deere Forum 02-11-2016, 08:54 PM
Replies: 3
Views: 3,394
Posted By jdgreen
What is the oil level like in the transmission? I...

What is the oil level like in the transmission? I suspect oil level may be too high and causing leakage into the brakes. There is no actual seal in the brake shaft. There should be a spiral groove in...
Forum: John Deere Forum 12-15-2015, 08:57 PM
Replies: 5
Views: 4,752
Posted By jdgreen
The foot operated pedal should have no effect on...

The foot operated pedal should have no effect on pto operation. The lever beside the seat operates the pto. If there is action on pto with foot pedal, I suspect the release bearing operating sleeves...
Forum: John Deere Forum 09-26-2015, 10:07 PM
Replies: 2
Views: 3,631
Posted By jdgreen
It sounds like you have a leak in the pto clutch...

It sounds like you have a leak in the pto clutch circuit. Could be blown orings or gasket at pto valve or blown seals in pto clutch piston or clutch drum.
Forum: John Deere Forum 06-09-2015, 08:35 PM
Replies: 6
Views: 7,277
Posted By jdgreen
You are correct, if you have clutch pressure and...

You are correct, if you have clutch pressure and can get it into gear, it should move. If it does not, then there is something physically broken or worn out. Clutch splines, clutch shaft, hi-lo,...
Forum: John Deere Forum 06-07-2015, 11:00 PM
Replies: 6
Views: 7,277
Posted By jdgreen
Do you have a pressure gauge you can check clutch...

Do you have a pressure gauge you can check clutch pressure with? Make sure pressure goes to zero when you push clutch down and you should have maybe 160 psi with clutch pedal released. Does the pto...
Forum: John Deere Forum 06-07-2015, 03:29 PM
Replies: 6
Views: 7,277
Posted By jdgreen
A couple of questions. What was on the screen...

A couple of questions. What was on the screen when you cleaned it? DO you have pictures of the material? What do you mean by the clutch works at idle? Will the tractor move at idle? What transmission...
Forum: John Deere Forum 09-28-2014, 09:32 PM
Replies: 2
Views: 3,466
Posted By jdgreen
When you say solenoid in dash, I assume you mean...

When you say solenoid in dash, I assume you mean the relay on the firewall? If the relay clicks when switch is turned and no power is going to the starter, then the relay is bad or the wire between...
Forum: John Deere Forum 09-28-2014, 09:26 PM
Replies: 1
Views: 3,435
Posted By jdgreen
I always use a small pair of channel locks ...

I always use a small pair of channel locks
(maybe 4 inch) to loosen and tighten the lower engine side of the tach cable. If your hour meter is still working, I doubt a new cable will make the tach...
Showing results 1 to 16 of 16

 
Forum Jump




All times are GMT -5. The time now is 08:58 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2002 - 2018, www.DotHQ.com