Search results

So the backhoe has been acting up after we blew a hose and replaced It. First the swing wouldn’t go left so I pulled the relief valve and cleaned put it back in and it worked for a minute then stopped working again. Tried again and then the slick quit working. Pulled valves cleaned put back and...

So when you start to move the 2016 1100c is louder and vibrates more until you get up to speed and let off the throttle a little bit. Then it smooths out and gets qouiter. Kinda like when the clutches shift on a sled or wheeler. Fluids are full. Is this normal any ideas why it does this?

2016 x1100c front wheels are not engaging in 4wd. Had chains on back with blower but couldn’t steer for crap so I moved the chains up front and noticed that the back tires are spinning but the front tires are doing nothing. Jacked all 4 wheels off ground and put in 4wd and the front tires move...

I’m looking for pictures of the k connect plow. I have the blower and want to fab up a plow to go onto the k connect. If anyone has pictures of the k connect plow side mounting brackets it would be a great help to my project. I’m looking at using a 6’ straight blade plow off a Jeep for my...

No one has an ideas why the hst is hesitating on my 2016 x1100c??? like i said push the pedal down (doesnt matter if its a 1/4" or all the way down) it takes a second for the trans to move the wheels? Is there a relief valve that controls this?? Charge pressure??? Any pics where this is...

Can the windshield on the x1100c open? I see some older models have gas struts and latches to open?

The radio in my x11ooc is loosing its memory. It doesn't happen every time the key is shut off so I'm suspecting a bad connection or relay. Has anyone had this problem, what was the cause.

So if I push the go pedal super slow I can get pretty smooth starts but if I jam on the pedal it revs up and takes 1-2 seconds before it starts to move and it jumps fwd. Also if I push on pedal normally it will jump fwd. any ideas??

When letting off the go pedal I can feel a clunk turns out it’s slop in the front upper a-arms. I did some searching on here and found a couple threads about it but no real fix. Has Kubota come up with a fix? My fix would be a couple shims on either side of the arm to take the slop out. Any...

Anyone have info on this https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F173432073753

Why hasn't Kubota added a grab handle like the one on the pass side on the drivers side? anyone come up with a handle for the x1100c?

New to us 2016 x1100 is pretty jerky when pushing go pedal and hst braking is a little harsh for our taste. My old 900 I installed the coast cave and liked the feel of that. Would like the new one to act the same. No cost valve available for this model, read there is an adjustment I can make to...

Who’s using what for boot guards on x1100c? Anyone lay eyes on the kubota ones?

What is the stock rim size and bolt pattern for 2016 x1100c? 4/110 12x8.5??

anyone have the k-connect installation instructions

Looking at a 2016 1100c with k connect and 66” blower has 1000hrs 1500miles on it. Their bottom dollar is 18000. Is this a good price? Any known problems with this year rtv and blower setup?

Looking at getting a new rtv x1100. How does the k connect system attach to the rtv? Does the system hinder ground clearance? How much of a job is it to remove the entire system in the summer months. Only planning on using it for plowing and snow blowing no summer attachments so I would be...

Anyone find some aftermarket rear shocks or front struts that will fit the rtv 900?

looking at getting a 3016 but the hoe doesn't offer hyd thumb, is there a kit out there that will fit the Mahindra 3720 hoe. if there is no kit out there will the woods bh80x hoe fit on this tractor?

Anyone have aftermarket u-joint numbers for the front drive shaft.