Search results

Bob did a fine job creating the Dash Retainer. He sent me the STL file and I printed same on my 3D printer. Turned out great and fit's perfect. Used 3M tape to install and does the job very nicely. Cheer's to Bob and Thanx again - a real asset to the group.

How can you define comparable oils without an oil labs quality and specification analysis? We all know synthetic is better than crude, which is what these machines like. I am a total believer of synthetic's, but they also have different subjective properties between brands. There has been many...

This is the one I used - has on/off switch. https://www.amazon.com/Upgraded-Charge-Qidoe-Aluminum-Voltmeter/dp/B08PTZ17NS/ref=psdc_2407759011_t2_B07FXH5ZZK.

You will be fine, The detergent values and viscosity are slightly different but not harmful. The remaining residual will be highly diluted and with no ill effect.

Stay with cast original design, dissimilar metals can be a problem when not designed as such.

That’s your Hydraulic tank strainer screen. I doubt it’s leaking there, look above on the inboard drivers side of tank. You will see a rubber cap on an unused nipple with a clamp. The rubber cap has been known to deteriorate and start leaking. Poor rubber composition and has been upgraded...

The bed control lever must be In the center/float position when not dumping. To eliminate your issue push the lever all the way down and then to the center, this will load the cylinder with down pressure. The lever has the folding plate for maintaining center lock. If you leave the lever locked...

I put a piece of 1/2 conduit on the latching pin and very slightly bent each pin for 0/zero latching clearance. This is just cold rolled steel and it worked like a champ. For the side panel inserts, I removed the panels and put a strip of self adhesive weather stripping down the full length of...

The second link shows option for has 5 different sizes up to 2.5 inches, the brush guard is only about 1.5 inches by memory.

Try These. The second link you can turn the rubber over for full coverage appearing outward. https://www.amazon.com/1-1-Vinyl-Coated-Clamps-Wd/dp/B01HH7TNFQ/ref=sr_1_16?crid=3L8CLR498K39D&keywords=RUBBER+COATED+CLAMPS&qid=1649112889&s=hi&sprefix=rubber+coated+clamps%2Ctools%2C138&sr=1-16...

I went through this with my RTV 1100 and my RTV X1100c. The bolt pattern on the 2019 RTV X1100C Is 4/110, This bolt pattern is commonly used on utility trailers. I bought my wheels from Side BY Side Stuff with chrome lug nuts. Wheels are System 3 ST-4 Gloss Black Wheel part number SBSS-9239...

Wow, God Bless you guys and stay safe, healthy and happy.

Look at it a little closer, the operating voltage is 9-32 vdc.

I have had mine for over 2 yrs and would buy again for sure. I have 2 handhelds that are rated at over a million candle power and it is much brighter than those. I saw the reviews and hard to believe, magnets are neodymium and very strong. I use them for alot of projects. Mine is cradled in the...

Hi Doc, Negative, the screen protector for the back window is optional. Very few that I see with them.

The one on the Right Rear also has an Antenna mount for your Radio, Pre-Wired and coax is stuffed in potential factory radio location. Overhead Console.

Yes, Custom made Mount and clamps on front Bumper with Ram Claw System. Quick wire interface & Remote Controlled. Very Powerful - Only used as needed. FSYF 7 Inch 50w Led Search Light 360 Degrees https://www.amazon.com/gp/product/B06XSVLFKK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1

If you are inclined to replace the boots yourself, they are not that expensive. https://www.powersportsid.com/kubota-cv-joints/

Antenna is a Austin Seeker & Connector is a BNC to SMA 90. The Remtronix REM-800B is a very good antenna also.

THE VERBIAGE JUNK WAS UNCALLED FOR! The Kubota is ARES-RACES certified.. Two Flavors of Amateur Radio Emergency Operation Emergency service is one of the basics of the Amateur Radio Service and there is sometimes come some confusion about ARES, the ARRL arm of emergency services and RACES...