Search results

Well it is that time to put new kicks on the ole girl. Man was I shocked too see the load capacity of the Mag 440's tires. It was 1675 lbs, that ruled out many of the tires that I had been looking at. What is everyone using on their rigs? At the OEM tires rating I can't seem to find much of...

I have a Swisher walk behind 24 in cut with the factory front wheel kit. It is like new and barely used bought it to clean up a camp site only to sell the campsite a couple of years later. Will take $1200 for it, location is around 30 mi south of Lexington ky. pm if interested and for pics.

good info here...tanks again

Had a mouse get in mine a couple of years ago, I closed the outside air vent and no problems since

va1100 -- Rite now I'm thinking of a holesaw to cut out a hole in the skidplate for access to the drain plug

followed your advice and sprayed wd 40 in and captured the results, it was rusty colored. After allowing it to run and somewhat reach temperature and shut it down the bell housing felt really warm too me. I wonder if the water is coming from condensation from warm metal and cold air, hence the...

Started to remove starter, pulled the bell housing plug and a pretty fair amount of water ran out. Placed a heater under the motor and warmed some more, left drain plug out and let drain for a few days. While it's draining I will change the oil and filter while I wait. The utv started fine again.

Well got home from church and the temp had warmed up to 36 deg and tried to start the Kubota to my surprise it fired rite off, next cleaned out a spot in the garage and put it on ramps and jack stands from what I see from the ground would be the best way to get to the starter unless someone...

First noticed was turn key no click no rotation, but now I'm able to be outside to better hear it turn key click heard and no rotation. have not checked drain plug just yet, -1 actual air temp.BBBBRRRRRRRR

no never have used a pressure washer on it. It has gone thru water maybe 6 in deep, surely that wouldn;t do it.

just an update, first thanks to Foxalaska, for the hint on the lights and everyone else that gave some very valuable info. I have a voltmeter and a dc ampmeter and with the help of my wife we went out and I checked the battery voltage and current, the no-load voltage was 12.8v, with just glow...

thanks everyone for your valued time to offer some suggestions, will try some if weather will cooperate just a little.

First off The problem rtv is a 2014 x1100c,and has not given one hint of any trouble until this cold snap we are presently in. Around Christmas day the rtv was tried to be started, it was given the glow cycle and then turned to start no click or anything happened. I thought the battery...

If I can upload pics,here's my simple fix to the problem. simply remove bottom clamp and use a electrical conduit clamp to gain the needed room for side rails. You will have too place the boards on the other side of the standard. Also I used a thin piece of rubber to take the extra room at the...

I went to my dealer today and questioned them about this. They had no clue as to what I was talking about. It took them several minutes checking online but they found the psb and ordered the parts for me. Sometimes I guess they are to busy to check or Kubota is failing to properly notify...

Bingo, I think you and pop58 nailed it replaced the inner filter and cleaned the diaphragm,the filter was very dirty and light didn't show thru it very well. Also fitch was also correct in that I also found it very dirty and stuck I do believe. I started the machine back up with everything...

yes I believe it is what you call a closed breather, the vent from the valve cover goes directly into the air intake manifold, I do believe..thanks

smoke seemed to be mostly white, with maybe just a little blue not much. thanks for asking

pop58, I did change the external (pre-filter), but not the internal...good call will check also...thanks

Thanks guys for the info provided. Looked up the item I removed and it is listed under the head cover section on the the rtv-x900w section. It is listed as item 050, with a Kubota part #1G911-05203 part name is called a comp valve breather. It basically vents the valve cover back into the intake...