Search results

I am using the float position on my remote when using a drum mower. The hydraulics heat up to the point that engaging gears is delayed. I have 700 hours on the tractor. My understanding of the valve is that the fluid should flow through the body the same as when in the neutral position so the...

Helping out a friend with his RTV. He shut it off one day and it hasn't started since. He had someone else look at before me. From what he said the fellow removed the injectors and looked them over, replaced the fuel filter, had him put an electric fuel pump bypassing the lift pump, and had him...

I have a 1100 and can't seem to keep water out of the hydraulics. Is there a case vent for the transmission or rear axle housing? I can't seem to find one. Thanks for any help.

The operator manual refers to "external auxiliary hydraulic control valve" supplement or manual that was packages with the manual. Does anyone have a source for this? I seem to have all but this one. Thanks

I had a gate cylinder leaking badly on my Hesston 5530. I purchased a pair of rebuild packing kits a while back but didn't understand at the time why it included a square rod in the kit. No instructions were included and no mention in the owners manual. Looking at the cylinder I wasn't sure as...

I had purchased two 1100's in which both had the compressors set up, pulley would not turn. There was no way I was going to pay what the dealer wanted for a compressor so I purchased a 11287C Universal Air Conditioner and a UAC RD10017C A/C Receiver Drier from ebay for a little less than $200...

On a 1100cw, what size gap do you have between the rubber stopper and the frame, unloaded? Mine has about an inch, I would think that there should be more of a gap. I would like to know what you have before I start taking things apart.

Driving around this evening I realized that I have a lot of light reflecting back to me from the silver grill guard. Has anyone been bothered by this? I don't have the roof lights hooked up yet. With the light reflecting back it distracts from seeing for me. I was thinking of painting the back...

I am replacing the rusted out floor of one of my 1100's and wanted to share the progress. Just to let everyone one know, I hate powder coating anything exposed to the element, give me Rust-Oleum any day. Once moisture gets under the coating it travels and rusts underneath and a lot of times it...

Does anyone have a scanned owners manual for a 2008 RTV1100 to share? Workshop manual if anyone wants it http://www.mediafire.com/file/n309iv4bu5oa3u7 Kubota RTV 1100 http://www.mediafire.com/file/eqa5h9n7v54i0cz Kubota RTV 900

I installed a bowl type filter on the RTV since I didn't care for the in-line filter. I made the bracket from thin angle rounding off the corners. I used a 6A320-58862 filter. I mounted it to the rear tapped hole on the frame. The filter has a third hose fitting in the center which I ran up to...

Does anyone have a source for the o-ring and backer for the quick connect? Mine are leaking and the dealer has no listing except the whole unit.

My windshield was offset to the right and would not latch closed. I loosened the hinges and adjusted the hinges in order to latch it but the hinges didn't look right to me. Are they supposed to be bent they way they are or did they get messed up and need bending back straight?

Cleaning up my action find and found something not so nice.

I would like to add a radio to the RTV I had just bought. It doesn't have one installed and the blank plate is missing, not sure if it had one installed in the past. Reading some of the posts it is mentioned that kubota had included a support bracket loose with these machines but mine doesn't...

Just bought a 2009 RTV1100 from an auction with a curtis plow. Would anyone have a copy of any documentation [owners manual] for the plow? The mounting plate wouldn't allow the plow to mount up, looks like it could have been jacked up using the center of the plate. I removed it and pushed it...