Gettin' in over our head.....

jwstewar

Senior Member
Staff member
Looking good!

I see you're going "smooth side out" on the OSB. I think I do it the other way but on walls, it doesn't matter as long as you're consistent so it doesn't show the different textures on the same wall (which may be hard to cover with paint).

Are you going to use plywood clips on the ceiling? I recall you had a pretty decent span between joists but was working on a solution to reduce the gap.

In the tack room I did not use plywood clips. It is only 8x8 so just two sheets. What I did was run a 2x4 parallel to the trusses. This cut the 4' span between the trusses to 2' and it also happened to fall right at the joint of the OSB. Since I'm able to put the screws right at the edges, I figured I won't need the clips. I've got one sheet up, I want to do the other one maybe tomorrow. I was able to get 4 sheets over last Friday. I put one sheet on the wall. One on the ceiling. Monica then used a sheet to cover a part of the metal in the barn area - after she miss-cut one and "ruined" it. Not a big deal, OSB is cheap and she was trying. How many women do you know that will run a circular saw?

Yep, we went with smooth side out on all of the OSB. If for not other reason, it catches less dirt - and believe me that is a concern in a barn with animals and a dirt floor. I believe we will paint the "exterior" walls of the milk room even though we haven't painted the rest of the OSB in the barn where the goats are. If it gets cold enough this weekend for the ground to freeze, I want to take more OSB to the barn. Right now with temps in the 50s (and some 60s) and tons of rain, we no longer have a solid base for a yard. In the good places it is more like a sponge or Jell-O. In other places it is more like Clam Chowder and you sink up to your knees. Makes it a little hard to get materials to the barn. If we had gravel it would help, but not really a good way to get a driveway there and normally not a lot of vehicle traffic will be going to the barn. A load of hay about every 5 weeks.
 

jwstewar

Senior Member
Staff member
Looking good!

I see you're going "smooth side out" on the OSB. I think I do it the other way but on walls, it doesn't matter as long as you're consistent so it doesn't show the different textures on the same wall (which may be hard to cover with paint).

Are you going to use plywood clips on the ceiling? I recall you had a pretty decent span between joists but was working on a solution to reduce the gap.

In the tack room I did not use plywood clips. It is only 8x8 so just two sheets. What I did was run a 2x4 parallel to the trusses. This cut the 4' span between the trusses to 2' and it also happened to fall right at the joint of the OSB. Since I'm able to put he screws right at the edges, I figured I won't need the clips.

Yep, we went with smooth side out on all of the OSB. If for not other reason, it catches less dirt - and believe me that is a concern in a barn with animals and a dirt floor. I believe we will paint the "exterior" walls of the milk room even though we haven't painted the rest of the OSB in the barn where the goats are. If it gets cold enough this weekend for the ground to freeze, I want to take more OSB to the barn. Right now with temps in the 50s (and some 60s) and tons of rain, we no longer have a solid base for a yard. In the good places it is more like a sponge or Jell-O. In other places it is more like Clam Chowder and you sink up to your knees. Makes it a little hard to get materials to the barn. If we had gravel it would help, but not really a good way to get a driveway there and normally not a lot of vehicle traffic will be going to the barn. A load of hay about every 5 weeks.
 

jwstewar

Senior Member
Staff member
We've never had two in the same bucket, but we had one that would take a water bucket and purposely knock it over, stick her head in it and pick it up. She would then walk around for hours at a time with it on her head or just stand in the field with it on. We always said she wasn't quite right. Unfortunately we lost her last year, she never quite rebounded from kidding last February and we kept fighting with her, but finally lost her end of May/first of June. She wasn't a great goat, had a decent body, but a small udder and a lopsided udder after her second kidding, but she was one of my favorites because of her personality. She used to love winter and when I would wear my Carhartts to the barn. She would love to rub her head on them, we were the same color when I did. Fortunately, we finally got 2 does out of her last year. The one looks like it has her body, but is looking like she will have a better udder (hoping she does), the other one is also looking nice, but a little different style of body, but also the udder is looking better. We will know more in a few weeks when they kid.
 

jwstewar

Senior Member
Staff member
OK, I've fallen way behind on keeping this thread updated. Been too busy working on the room to tell about the room.:whistling:

We are getting real close to finishing. At this point it is functional. The electrical is all done. Plumbing is finished other than a hot water outlet for a water hose to bath animals.

Most of these pictures are pretty self explanatory except for maybe why we only painted so far down the walls. We are going to put metal to about 3' up the wall to make spills and splashes easier to clean-up. We still need to coat the floor with something. They covered the basement floor (high rise 12 story building) at work with some type of epoxy that seemed like it leveled and smoothed the floor out. So I want to do something similar. Then I'll do the rubber commercial baseboard and then finally the metal.

As you can see we have the milk machine in there and we are now able to start using it. We are milking 10 or 11 goats (I don't know, it changes daily) right now, so this is saving a lot of my wife's and daughter's hands.

The water heater is a RHEEM RTE9 - 9000 watt electric unit. It is a 220volt 40/amp unit. Rated at 3 GPM - uh yeah, no. It is working OK for how we want to use it. If we keep the flow at the faucet turned down the water will get hot. Yesterday we bathed a goat so I took the aerator off and hooked a water hose up. The water was warm. It kept the goat from getting cold, but it wasn't hot. Which is OK, we don't need it hot, just not ice cold for them.

Don't know if I attached a picture, but a 220 volt 20 Amp outlet is wired in for a window/wall AC Unit Unit. It is also a heat pump with electric heat strips as a back-up. That will be the heating and cooling for this room. I know the AC side will be OK, a little worried about the heating side. But we aren't looking at keeping this room 75 degrees either. Closer to 50 - 60 to give us a place to get warm or take a new born baby to warm up and keep stuff from freezing. I think it'll do that.

Oh, forgot to mention the lights. These are enclosed shop lights. They are 5200 Lumen, I think 4000k LED lights. There are two of them, now that the room is white it is plenty bright. There will still be a ceiling fan installed yet with an LED light as well, so the room should be plenty bright enough for normal chores as well as doing AI of the goats.
 

Attachments

  • 20170408_220659.jpg
    20170408_220659.jpg
    59.7 KB · Views: 21
  • 20170414_165223 (9).jpg
    20170414_165223 (9).jpg
    14.2 KB · Views: 20
  • 20170416_100549.jpg
    20170416_100549.jpg
    32.3 KB · Views: 21
  • 20170416_100610.jpg
    20170416_100610.jpg
    26.7 KB · Views: 20
  • 20170408_220634.jpg
    20170408_220634.jpg
    65.9 KB · Views: 21
  • 20170416_100616.jpg
    20170416_100616.jpg
    19.5 KB · Views: 21
  • 20170414_165240 (7).jpg
    20170414_165240 (7).jpg
    20.7 KB · Views: 22

jwstewar

Senior Member
Staff member
Thought I better post an update. We had kind of "paused" on the milk room. Earlier this year Monica decided to finish it - and in the process remodel it, LOL. So she started working on it. She ended up doing most of the finish work herself. I help her with the metal.

We also had to redo the drain. I had originally tried a dry sump 55 gallon barrel. That didn't work, water table is too high and it stayed full. I ran almost 350' of 2" Schedule 80 to the front road ditch for draining the sink water.
 

Attachments

  • 20200203_210021_resized.jpg
    20200203_210021_resized.jpg
    60.8 KB · Views: 12
  • 20200505_213547_resized.jpg
    20200505_213547_resized.jpg
    41.2 KB · Views: 11
  • 20200505_213541_resized.jpg
    20200505_213541_resized.jpg
    61.4 KB · Views: 11
  • 20200505_213534_resized.jpg
    20200505_213534_resized.jpg
    51.9 KB · Views: 12
  • 20200505_213524_resized.jpg
    20200505_213524_resized.jpg
    56.4 KB · Views: 11
  • 20200505_213522_resized.jpg
    20200505_213522_resized.jpg
    61.6 KB · Views: 11
  • 20200505_211347_resized.jpg
    20200505_211347_resized.jpg
    62.9 KB · Views: 10
  • 20200505_210005_resized.jpg
    20200505_210005_resized.jpg
    59.1 KB · Views: 12
  • 20200203_210012_resized.jpg
    20200203_210012_resized.jpg
    66.1 KB · Views: 12
  • 20200203_210006_resized.jpg
    20200203_210006_resized.jpg
    57.4 KB · Views: 12
  • 20200505_211350_resized.jpg
    20200505_211350_resized.jpg
    74.9 KB · Views: 12

Jim_S

Super Moderator
SUPER Site Supporter
Gold Site Supporter
Thought I better post an update. We had kind of "paused" on the milk room. Earlier this year Monica decided to finish it - and in the process remodel it, LOL. So she started working on it. She ended up doing most of the finish work herself. I help her with the metal.

We also had to redo the drain. I had originally tried a dry sump 55 gallon barrel. That didn't work, water table is too high and it stayed full. I ran almost 350' of 2" Schedule 80 to the front road ditch for draining the sink water.

Looks GREAT!
 

bczoom

Senior Member
Staff member
Gold Site Supporter
Yes it does look great!
Love the plywood. ;)
Also love that Pyle thermometer on the wall. I have a couple of those. Better than most any other I've owned.
 

jwstewar

Senior Member
Staff member
Yes it does look great!
Love the plywood. ;)
Also love that Pyle thermometer on the wall. I have a couple of those. Better than most any other I've owned.

Wonder where that came from, LOL.

I'm down to one sheet left. It is going to pain me to have to start buying OSB for projects again, LOL.
 

bczoom

Senior Member
Staff member
Gold Site Supporter
You know how lazy I am? The sheets I didn't sell as they were dedicated for a project I had... are still sitting there. They're needed to finish the ceiling in my one building but there's so much "stuff" in the building that emptying it all out to get to the ceiling is overwhelming to my motivation. :(
 
Top