![]() |
#1
|
|||
|
|||
![]()
I am having problems on how to properly clean the air filter on a Massey Ferguson 35. Diesel if it matters. Any information would certainly be helpful, thanks in advance.
Jim |
#2
|
|||
|
|||
![]()
Welcome to the forum.
Is that the conical filter with a separate inner air filter? Looks something like the pic below? If so, the outer filter can be cleaned using an air compressor and it's best to blow from the inside of the filter out (or use a shop vac and suck the debris off the outer filter). The inner filters aren't really supposed to be cleaned as the cleaning process can loosen particles which then get sucked into the engine. It's best to just replace these when they get dirty. |
The Following User Says Thank You to bczoom For This Useful Post: | ||
Doc (09-07-2018) |
#3
|
||||
|
||||
![]()
How many times can you blow out a filter like the one pictured and put it back in service?
I found something like 'Kubota 1989' on one of those once. No blowby so I doubt the engine ever ate dust, but it seems the prior owner just kept blowing out the filter and re-using it. The tractor wasn't a Kubota, so hopefully this was just old stock bought more recently and hadn't been in the tractor as long as I feared. It wasn't very dirty but I replaced it immediately. That tractor came from an urban landscape contractor so hopefully it hadn't experienced as much dust as a farm tractor.
__________________
|
The Following User Says Thank You to California For This Useful Post: | ||
Doc (09-07-2018) |
#4
|
|||
|
|||
![]()
If you blow them out from the inside of the filter to the outside or use a vacuum, they can last quite awhile and get several cleanings. What kills their life is when you clean and pack dust/dirt/debris into the filter, it starts clogging similar to a AC-1 furnace filter. It then can't pull the air it needs and your engine will starve for air.
A good way to tell if your filter is getting clogged. When the engine is running pull the filter off slowly and just a little bit so there's only a small air gap . If when pulling it off slowly, there's a change in engine RPM's or extreme sucking at that minor gap, your filter is pretty clogged. They're normally not that expensive if you shop around. I can find the inner and outer filters combined for around $30. CA - I'm guessing that was a old stock but newly installed filter. Being a landscape contractor, he probably keeps a large stock in the shop. |
The Following User Says Thank You to bczoom For This Useful Post: | ||
Doc (09-07-2018) |
#5
|
||||
|
||||
![]()
Yeah I'm hoping that element was just old stock.
What does your inner filter look like? It isn't used on the small Yanmars. Only the element in your photo, precede by a cyclone-baffle dust trap on top that's visible on the left in my sig photo below, and this old photo. http://nettractortalk.com/forums/att...0&d=1246346793
__________________
|
The Following User Says Thank You to California For This Useful Post: | ||
Doc (09-07-2018) |
#6
|
|||
|
|||
![]()
This is a generic photo but when you have both inner and outer filters, here's something of what they look like. The inner obviously slides inside the outer.
Haven't looked at my Deere tractor filter lately to see exactly what's in it but this inner/outer setup is what's in my RTV and ZTR. ![]() |
The Following 3 Users Say Thank You to bczoom For This Useful Post: | ||
#7
|
||||
|
||||
![]()
Thanks. I learned something new.
__________________
|
The Following User Says Thank You to California For This Useful Post: | ||
Doc (09-07-2018) |
![]() |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |