Net Tractor Talk
       

Go Back   Net Tractor Talk > Owners & Operators Forums > Mechanical issues and Paint & Restorations Forum

Mechanical issues and Paint & Restorations Forum Show us how you make em pretty.

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 03-28-2011, 09:05 PM
shinnlinger's Avatar
shinnlinger shinnlinger is offline
Senior Member
 
Join Date: Oct 2007
Location: Canaan, NH
Posts: 394
Thanks: 0
Thanked 0 Times in 0 Posts
shinnlinger will become famous soon enough
Default Kubota front axle seals

HI,

Out at the barn this weekend and noticed a fair bit of fluid draining from the bottom of one of my front axle portals. A quick inspection confirmed the bottom cap had popped off much like a freeze plug and that the other side was popped as well, but no fluid telling me I missed that one and have probably run the tractor for a period of time (3hrs maybe over 3 months) with no fluid in that side of the axle.

There has been weeping from the top pivot seals for some time but it didn't seem that severe and I tried to keep an eye on the fluid but again, must have missed the first pop. My suspicion was that over time enough water got in the axle thru the leaky top seal and condensation that it froze and popped the cap off.

Having seen similar axle seal replacements on the web they don't seem that difficult, so I asked my father to stop by the dealer and get a parts schematic, since he was going by. He went one further and talked to a tech who in addition to confirming the ease of replacing the bottom caps, also said it happened all the time, but instead of freezing water, thought it was due to the changes in temperature as the castings expand and contract and recommended just replacing the bottom caps and to top up with 80 wght gear oil, not the hydro fluid Kubota recomends

I'm pretty sure the ball bearings are probably fine despite the lack of lubricant, should I follow the tech's advice and just press on new caps and refill. My gut tells me this really will be fine but before the techs report, I had intended to disassemble the portals's and replace the upper seals as well and inspect the bearings.

Would you use silicone on the bottom cap seals? Would you use 80 wgt vs hytran?

Thanks.

Dave
__________________
Shinnlinger

'85 kubota 34 horse L2850
Reply With Quote
  #2  
Old 03-29-2011, 04:21 AM
ki0ho's Avatar
ki0ho ki0ho is offline
Super Site Supporter
 
Join Date: Jan 2010
Location: Lake of the Ozarks
Posts: 102
Thanks: 1
Thanked 2 Times in 2 Posts
ki0ho is on a distinguished road
Style:
Default front axle

Yes I would and not have any worrys......as there is no shifting to be done in the front axel.......I had a seal start leaking on my M/F and being still in warenty they replaced it but the service manager said that if it started leaking latter to drain and use 80/90 weight and it should be fine.......in the trans going to the heavyer lube could make it hard to shift in cold weather.. hope this helps ya......
Reply With Quote
  #3  
Old 03-29-2011, 05:18 AM
Cowboy's Avatar
Cowboy Cowboy is offline
Senior Member
 
Join Date: Aug 2009
Location: SC Kansas
Posts: 262
Thanks: 0
Thanked 0 Times in 0 Posts
Cowboy is on a distinguished road
Default

I'll just add I wouldn't use silicone for anything these days . Get you a can of "The Right Stuff" Rubber gasket maker for the lower end caps , its the best sealer of any type I have found . http://www.google.com/products/catal...d=0CGUQ8gIwBQ#

I couldn't find any new lower seal caps for my import tractor when I tore the front end down for repair & really screwed the old caps up getting them off . I used that stuff around the crooked edges & tapped them back in and it seals great . I also dont use gaskets on anything anymore either since I started using this stuff . best thing they invented since Beer. Best of luck
__________________
"Whoever said the pen is mightier than the sword obviously never
encountered automatic weapons." - General MacArthur
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





All times are GMT -5. The time now is 04:44 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2002 - 2018, www.DotHQ.com