Net Tractor Talk
       

Go Back   Net Tractor Talk > Owners Operators and Farming Forums > Livestock Forum

Reply
 
Thread Tools Search this Thread Display Modes
  #121  
Old 01-26-2017, 08:43 AM
jwstewar's Avatar
jwstewar jwstewar is offline
Senior Member
 
Join Date: Apr 2007
Location: South-Central Ohio
Posts: 679
Thanks: 12
Thanked 76 Times in 55 Posts
jwstewar is on a distinguished road
Default

Quote:
Originally Posted by bczoom View Post
Looking good!

I see you're going "smooth side out" on the OSB. I think I do it the other way but on walls, it doesn't matter as long as you're consistent so it doesn't show the different textures on the same wall (which may be hard to cover with paint).

Are you going to use plywood clips on the ceiling? I recall you had a pretty decent span between joists but was working on a solution to reduce the gap.
In the tack room I did not use plywood clips. It is only 8x8 so just two sheets. What I did was run a 2x4 parallel to the trusses. This cut the 4' span between the trusses to 2' and it also happened to fall right at the joint of the OSB. Since I'm able to put the screws right at the edges, I figured I won't need the clips. I've got one sheet up, I want to do the other one maybe tomorrow. I was able to get 4 sheets over last Friday. I put one sheet on the wall. One on the ceiling. Monica then used a sheet to cover a part of the metal in the barn area - after she miss-cut one and "ruined" it. Not a big deal, OSB is cheap and she was trying. How many women do you know that will run a circular saw?

Yep, we went with smooth side out on all of the OSB. If for not other reason, it catches less dirt - and believe me that is a concern in a barn with animals and a dirt floor. I believe we will paint the "exterior" walls of the milk room even though we haven't painted the rest of the OSB in the barn where the goats are. If it gets cold enough this weekend for the ground to freeze, I want to take more OSB to the barn. Right now with temps in the 50s (and some 60s) and tons of rain, we no longer have a solid base for a yard. In the good places it is more like a sponge or Jell-O. In other places it is more like Clam Chowder and you sink up to your knees. Makes it a little hard to get materials to the barn. If we had gravel it would help, but not really a good way to get a driveway there and normally not a lot of vehicle traffic will be going to the barn. A load of hay about every 5 weeks.
__________________
Jim
http://www.facebook.com/floweringgoatfarm
"What did you break now?"
Reply With Quote
  #122  
Old 01-26-2017, 08:43 AM
jwstewar's Avatar
jwstewar jwstewar is offline
Senior Member
 
Join Date: Apr 2007
Location: South-Central Ohio
Posts: 679
Thanks: 12
Thanked 76 Times in 55 Posts
jwstewar is on a distinguished road
Default

Quote:
Originally Posted by bczoom View Post
Looking good!

I see you're going "smooth side out" on the OSB. I think I do it the other way but on walls, it doesn't matter as long as you're consistent so it doesn't show the different textures on the same wall (which may be hard to cover with paint).

Are you going to use plywood clips on the ceiling? I recall you had a pretty decent span between joists but was working on a solution to reduce the gap.
In the tack room I did not use plywood clips. It is only 8x8 so just two sheets. What I did was run a 2x4 parallel to the trusses. This cut the 4' span between the trusses to 2' and it also happened to fall right at the joint of the OSB. Since I'm able to put he screws right at the edges, I figured I won't need the clips.

Yep, we went with smooth side out on all of the OSB. If for not other reason, it catches less dirt - and believe me that is a concern in a barn with animals and a dirt floor. I believe we will paint the "exterior" walls of the milk room even though we haven't painted the rest of the OSB in the barn where the goats are. If it gets cold enough this weekend for the ground to freeze, I want to take more OSB to the barn. Right now with temps in the 50s (and some 60s) and tons of rain, we no longer have a solid base for a yard. In the good places it is more like a sponge or Jell-O. In other places it is more like Clam Chowder and you sink up to your knees. Makes it a little hard to get materials to the barn. If we had gravel it would help, but not really a good way to get a driveway there and normally not a lot of vehicle traffic will be going to the barn. A load of hay about every 5 weeks.
__________________
Jim
http://www.facebook.com/floweringgoatfarm
"What did you break now?"
Reply With Quote
  #123  
Old 02-01-2017, 01:17 AM
California's Avatar
California California is offline
Super Moderator

 
Join Date: Apr 2007
Location: Sonoma County (Wine country N of San Francisco)
Posts: 1,511
Thanks: 159
Thanked 360 Times in 211 Posts
California will become famous soon enough
Style: VB_Blue
Default

Hey Jim,

Do your goats ever do this ...

https://youtu.be/Ws_YDoqrCtc

(how the heck do you embed a youtube video here?)

BCZOOM edit:
Remove the s in https normally fixes it but not in this case.

http://www.youtube.com/watch?v=Ws_YDoqrCtc
__________________
Reply With Quote
  #124  
Old 02-02-2017, 02:54 PM
jwstewar's Avatar
jwstewar jwstewar is offline
Senior Member
 
Join Date: Apr 2007
Location: South-Central Ohio
Posts: 679
Thanks: 12
Thanked 76 Times in 55 Posts
jwstewar is on a distinguished road
Default

We've never had two in the same bucket, but we had one that would take a water bucket and purposely knock it over, stick her head in it and pick it up. She would then walk around for hours at a time with it on her head or just stand in the field with it on. We always said she wasn't quite right. Unfortunately we lost her last year, she never quite rebounded from kidding last February and we kept fighting with her, but finally lost her end of May/first of June. She wasn't a great goat, had a decent body, but a small udder and a lopsided udder after her second kidding, but she was one of my favorites because of her personality. She used to love winter and when I would wear my Carhartts to the barn. She would love to rub her head on them, we were the same color when I did. Fortunately, we finally got 2 does out of her last year. The one looks like it has her body, but is looking like she will have a better udder (hoping she does), the other one is also looking nice, but a little different style of body, but also the udder is looking better. We will know more in a few weeks when they kid.
__________________
Jim
http://www.facebook.com/floweringgoatfarm
"What did you break now?"
Reply With Quote
  #125  
Old 04-17-2017, 11:30 AM
jwstewar's Avatar
jwstewar jwstewar is offline
Senior Member
 
Join Date: Apr 2007
Location: South-Central Ohio
Posts: 679
Thanks: 12
Thanked 76 Times in 55 Posts
jwstewar is on a distinguished road
Default

OK, I've fallen way behind on keeping this thread updated. Been too busy working on the room to tell about the room.

We are getting real close to finishing. At this point it is functional. The electrical is all done. Plumbing is finished other than a hot water outlet for a water hose to bath animals.

Most of these pictures are pretty self explanatory except for maybe why we only painted so far down the walls. We are going to put metal to about 3' up the wall to make spills and splashes easier to clean-up. We still need to coat the floor with something. They covered the basement floor (high rise 12 story building) at work with some type of epoxy that seemed like it leveled and smoothed the floor out. So I want to do something similar. Then I'll do the rubber commercial baseboard and then finally the metal.

As you can see we have the milk machine in there and we are now able to start using it. We are milking 10 or 11 goats (I don't know, it changes daily) right now, so this is saving a lot of my wife's and daughter's hands.

The water heater is a RHEEM RTE9 - 9000 watt electric unit. It is a 220volt 40/amp unit. Rated at 3 GPM - uh yeah, no. It is working OK for how we want to use it. If we keep the flow at the faucet turned down the water will get hot. Yesterday we bathed a goat so I took the aerator off and hooked a water hose up. The water was warm. It kept the goat from getting cold, but it wasn't hot. Which is OK, we don't need it hot, just not ice cold for them.

Don't know if I attached a picture, but a 220 volt 20 Amp outlet is wired in for a window/wall AC Unit Unit. It is also a heat pump with electric heat strips as a back-up. That will be the heating and cooling for this room. I know the AC side will be OK, a little worried about the heating side. But we aren't looking at keeping this room 75 degrees either. Closer to 50 - 60 to give us a place to get warm or take a new born baby to warm up and keep stuff from freezing. I think it'll do that.

Oh, forgot to mention the lights. These are enclosed shop lights. They are 5200 Lumen, I think 4000k LED lights. There are two of them, now that the room is white it is plenty bright. There will still be a ceiling fan installed yet with an LED light as well, so the room should be plenty bright enough for normal chores as well as doing AI of the goats.
Attached Images
File Type: jpg 20170408_220634.jpg (65.9 KB, 21 views)
File Type: jpg 20170408_220659.jpg (59.7 KB, 21 views)
File Type: jpg 20170414_165223 (9).jpg (14.2 KB, 20 views)
File Type: jpg 20170414_165240 (7).jpg (20.7 KB, 22 views)
File Type: jpg 20170416_100549.jpg (32.3 KB, 21 views)
File Type: jpg 20170416_100610.jpg (26.7 KB, 20 views)
File Type: jpg 20170416_100616.jpg (19.5 KB, 21 views)
__________________
Jim
http://www.facebook.com/floweringgoatfarm
"What did you break now?"
Reply With Quote
The Following User Says Thank You to jwstewar For This Useful Post:
bczoom  (04-17-2017)
  #126  
Old 07-13-2020, 05:00 PM
jwstewar's Avatar
jwstewar jwstewar is offline
Senior Member
 
Join Date: Apr 2007
Location: South-Central Ohio
Posts: 679
Thanks: 12
Thanked 76 Times in 55 Posts
jwstewar is on a distinguished road
Default

Thought I better post an update. We had kind of "paused" on the milk room. Earlier this year Monica decided to finish it - and in the process remodel it, LOL. So she started working on it. She ended up doing most of the finish work herself. I help her with the metal.

We also had to redo the drain. I had originally tried a dry sump 55 gallon barrel. That didn't work, water table is too high and it stayed full. I ran almost 350' of 2" Schedule 80 to the front road ditch for draining the sink water.
Attached Images
File Type: jpg 20200203_210006_resized.jpg (57.4 KB, 12 views)
File Type: jpg 20200203_210012_resized.jpg (66.1 KB, 12 views)
File Type: jpg 20200203_210021_resized.jpg (60.8 KB, 12 views)
File Type: jpg 20200505_210005_resized.jpg (59.1 KB, 12 views)
File Type: jpg 20200505_211347_resized.jpg (62.9 KB, 10 views)
File Type: jpg 20200505_213522_resized.jpg (61.6 KB, 11 views)
File Type: jpg 20200505_213524_resized.jpg (56.4 KB, 11 views)
File Type: jpg 20200505_213534_resized.jpg (51.9 KB, 12 views)
File Type: jpg 20200505_213541_resized.jpg (61.4 KB, 11 views)
File Type: jpg 20200505_213547_resized.jpg (41.2 KB, 11 views)
File Type: jpg 20200505_211350_resized.jpg (74.9 KB, 12 views)
__________________
Jim
http://www.facebook.com/floweringgoatfarm
"What did you break now?"
Reply With Quote
The Following 3 Users Say Thank You to jwstewar For This Useful Post:
bczoom  (07-14-2020), Doc  (07-27-2020), Jim Slagle  (07-13-2020)
  #127  
Old 07-13-2020, 05:12 PM
Jim Slagle's Avatar
Jim Slagle Jim Slagle is offline
Stuper Modulator

 
Join Date: Apr 2007
Posts: 2,008
Thanks: 1,615
Thanked 249 Times in 162 Posts
Jim Slagle will become famous soon enoughJim Slagle will become famous soon enough
Default

Quote:
Originally Posted by jwstewar View Post
Thought I better post an update. We had kind of "paused" on the milk room. Earlier this year Monica decided to finish it - and in the process remodel it, LOL. So she started working on it. She ended up doing most of the finish work herself. I help her with the metal.

We also had to redo the drain. I had originally tried a dry sump 55 gallon barrel. That didn't work, water table is too high and it stayed full. I ran almost 350' of 2" Schedule 80 to the front road ditch for draining the sink water.
Looks GREAT!
__________________
Did I just find this rope or have I lost my horse??

Forums Forums .com +++ Net Cooking Talk Forums
Reply With Quote
  #128  
Old 07-14-2020, 10:20 AM
bczoom bczoom is online now
Senior Member

 
Join Date: Apr 2006
Posts: 6,209
Thanks: 357
Thanked 926 Times in 615 Posts
bczoom is just really nicebczoom is just really nicebczoom is just really nicebczoom is just really nice
Default

Yes it does look great!
Love the plywood.
Also love that Pyle thermometer on the wall. I have a couple of those. Better than most any other I've owned.
Reply With Quote
  #129  
Old 07-27-2020, 12:28 PM
jwstewar's Avatar
jwstewar jwstewar is offline
Senior Member
 
Join Date: Apr 2007
Location: South-Central Ohio
Posts: 679
Thanks: 12
Thanked 76 Times in 55 Posts
jwstewar is on a distinguished road
Default

Quote:
Originally Posted by bczoom View Post
Yes it does look great!
Love the plywood.
Also love that Pyle thermometer on the wall. I have a couple of those. Better than most any other I've owned.
Wonder where that came from, LOL.

I'm down to one sheet left. It is going to pain me to have to start buying OSB for projects again, LOL.
__________________
Jim
http://www.facebook.com/floweringgoatfarm
"What did you break now?"
Reply With Quote
  #130  
Old 07-27-2020, 01:20 PM
bczoom bczoom is online now
Senior Member

 
Join Date: Apr 2006
Posts: 6,209
Thanks: 357
Thanked 926 Times in 615 Posts
bczoom is just really nicebczoom is just really nicebczoom is just really nicebczoom is just really nice
Default

You know how lazy I am? The sheets I didn't sell as they were dedicated for a project I had... are still sitting there. They're needed to finish the ceiling in my one building but there's so much "stuff" in the building that emptying it all out to get to the ceiling is overwhelming to my motivation.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





All times are GMT -5. The time now is 08:33 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Copyright 2002 - 2020, www.DotHQ.com