Search results

It sounds like you either ordered the incorrect rings or they sent you the incorrect rings. Third option would be somebody had been into this engine before, changed out pistons and sleeves with a aftermarket set.

The past year, he has brought home a bunch of big boy toys to use on the weekends around the farm. I think I will keep him around for a while.....he is turning out to be quite handy.....:beer:

6-10 ton vibratory. Son-in-law works for a CAT dealership. He can bring home a demo unit on a weekend.....

We can get millings down here in Tn. They are doing so much interstate construction and resurfacing, the plant has a massive pile in one of the side lots. I don't want to put any down until after I build my equipment barn. I'll need a couple of trucks of concrete for the slab and I don't want...

Asphalt millings are a great topcoat, also. The rest of my farm lane has a 2b gravel base, with 7" deep asphalt millings applied and rolled in. Just like pavement.....until the 80,000 pound cement truck rolls down it during the rainy season.

I top coated my drive close to the house and parking area with crusher run. It's a mixture of crushing fines and small stone. Easy to spread, level and back pull, packs in like cement when water is sprayed on it while compacting. Don't try to compact while dry.

Why not just take the power directly from the battery for your winch? Much easier to access. What wire gauge does your winch require? What is the FLA of your winch?

Mine is a 2023

Haha. I just got the letter from them...evidentially 7 months after a lot of other people got the letter. Maybe they started with the oldest units and the newer ones are at the end of the list?

From what I have seen, the complete wiring harness is already installed within the vehicles. The fuses maybe installed, also. You just buy Kubotas gold plated devices and plug them in along with the rocker switch that should come with them. If you look at the schematic, there is already a 20A...

Shocking enough, I got a call out of the blue, from my Kubota dealer today. They are coming out to the farm and are going to do the recall "repair" on site. No service call fee. Nice. Now if I could only get my John Deere dealer to do the same........Time will tell what the Cat dealership...

You might want to consult the 3rd section of the WSM. Looks like it answers most of your questions by just looking at the schematic.

Did anyone get this recall notice from Kubota for the RTV lineup? I am going to call tomorrow to see if they might come pick it up and deliver it on Kubotas dime. If they won't come get it, I guess I will torque the ball joint bolt myself, unless the bolt was the incorrect grade or they had...

I suspect the steering wheel hub is probably plastic or some type on nylon. Take the nut off, put a few drops of Kroil on the shaft and let is sink in for a bit. Tap on the bottom of it upwards with a 2 to 3 pound hammer. If that doesn't move it, grab your large 3 fingered wheel puller, apply...

Found one other pic with the dash disassembled. It shows the water valve for the heater. Just above it should be the air vent controller swing arm piece. Hope that helps a bit.

These screen captures are out of the 2021 WSM, so there just isn't a lot of pics available. But, this shows where everything is in an exploded diagram.

I believe, the control arm circled in red is what controls the air to the different vents. Make sure your cable isn't bent, rusted or kinked. I would also disconnect the cable and ensure that the actuator can move manually. Lube up the cable and sheath with some dry graphite.

What Trump said is he was going to roll back the EPA standards back to 2020, before he left office. I don't believe there was any mention of eliminating DEF on diesels. Tier 4 final was passed back in 2004 and was final phased in by 2014. DEF was required on larger diesels starting in late...

I bought one new in 2000. Tough little tractor. Had the 70 FEL on it. Did a ton of work with it on my farm when I first bought it. About 2009, I sold it to get a new 5055D. I needed more HP and weight to continue with bigger projects. Only problem I had with it was the tie rod for the...

I also waited for Kubota to come up with some type of front mounted mower. Since they ignored my wishes and I wanted a mower I could use before I take a dirt nap, I said "screw e'm" and bought a real front mounted mower........😀