Search results

I bought a Kioti tractor (22 hp) back in 1998, just this year I've had to replace the injectors. Kioti products are nothing to sneer at ☺

when our ancestors settled this country there were few lawyers and fewer laws. In this case the killer would never have seen a jail cell. Following history it seems the scum outnumbered law abiding citizens. Written history does not reflect when the 1st group of vigilantes were formed, however...

A lot of dealers started out as small repair shops, plus many large tractor dealers started carrying 4 wheelers and side by sides because their customers expressed a interest. Kubota does does have traveling tech people that visit the dealers. With all of that, Kubota problems with their...

The only way short of a turbo charger:clap:

Would highly recommend you follow the manual regarding break in procedures ☺☺

When you get it finished post some pictures! Good luck and keep all four wheels on the ground ☺☺☺☺☺

Bill, I had occasion to visit one of the oldest Kioti dealers in Washington State, I took your information with me and had a long chat with the boss and his chief trouble shooter, as I kinda suspected they both said your 18hp tractor would be grossly overloaded with the backhoe you have, which...

Doing a online search "PTO Hyd pump made USA" is a good place to start, you will have a big assortment of pumps to look at. The shaft size is not that important as all farm implement stores will carry adapters in various lengths sizes. These same stores might be a good contact to finding a...

Can you ask around and find a tractor to look at that has a PTO driven pump? Anyone that sells tractor mounted log spliters should be a good place to start. I bought mine from Northern Tool about 10 years ago This would be a huge help in deciding how to tie your pump to the tractor "I use a...

You are asking questions that I would have known 40 years ago☺ but the answer is both yes and no. It depends on the pump type and my dim memory says that a vane pump you can adjust the out put by the speed. The gear pump is designed to work best one general speed You do intend to buy a new...

Have fun ☺

That small of a difference in pump speed shouldn't make a dif, but to be on the safe side when you contact Mahindra they will have someone experienced in Hyds that can answer your question. When you are using the hoe that is what will heat your oil up, not the pump. It seems the new hoes...

The webpage for Mahindra shows their new hoes have relief valves, I would assume their older models also have a relief valve. However I try hard not to assume anything, a email or phone call to their service department should clear that up.

:myopinion: Your pockets are a little deeper than mine, a good floor deserves a good planer :-) and you are going to have a ton of fun! Are you aware of this site? they have one section on sawmills and a million good tips http://http://www.woodweb.com/KnowledgeBase/KBIndex.html

My pump came with the wood splitter which has it's own 5 gal tank. I'm not sure what it's GPM is. Does the backhoe have its own oil tank or was it made to run off the tractor hyds ? if not you are going to need a tank, you might be smart to contact the backhoe maker with technical questions ☺...

my low gear is 540 rpm, 2nd gear is 700 rpm which I've found best for the brush chipper

I would think so, the only time you will put a heavy load on the engine would maybe digging in hard ground or pulling stumps

I have a pump on my 22hp LB2204 which powers a wood spliter. On big blocks if you aren't careful you can kill the engine. I suspect as long as you are careful your 17hp will easily handle the backhoe. My machine has a 3 speed pto and I have to use the the lowest speed

Mills are addictive☺ Is their a kiln dry anywhere close to you? I prefer air dry but to get wood dry enough for a floor takes a long time. You can find on the internet good instructions for building small kilns where you can build your own. Keep posting photos, I'll bet you will be the tipping...

sounds like a lineament problem between the engine and bell housing which could only be caused by something not being machined correctly from the factory. I don't know much about Kiotis just what I've picked up over the years from my lb2204, sounds like your dealer should have replaced your...