Search results

Mork, The part Aurthuritis is talking about was added to units after S/N 18012. It is number 045, part # K7591-17490 on the attached snip. I have a 2014 model that I added them to and that took care of the clunk, I bought them from the Kubota dealer, they weren't very expensive. Pete

Is there any chance that there is air in one of the fuel lines? I installed the SWAG turbo kit on my X1100C, the instructions were a little different, I had to pull the injection pump and remove a shim to change the pump timing. When I started it up I had to bleed the lines twice, the first...

Colorado High, I don’t think it was due to suspension travel issues all by itself. I have a Kubota V blade on my X1100, which has downforce and have never had any issues. I also have a two inch lift on both units and 27” tires on both as well, the lift does increase the angle on the axles...

I bought second unit over the summer, an X1140. The first time I had to use four wheel drive the front left axle snapped at the outboard CV joint, it only had 15 miles on it. The dealer replaced it without any questions, it wasn’t abused, I’ve had my X1100 in this area many times with no...

Aurthuritis, I didn’t really notice much difference in speed one way or the other. Pete

Aurthuritis, I just did it for ground clearance, I was dragging the bottom over too many rocks. I ended up adding a 2” lift as well, between the two it made a huge difference in ground clearance. Pete

Aurthuritis, The wheel is a 14 x 8, backspace of 4, and offset of -10.2. I think Delta makes a steel wheel that will work, if I had it to do over again I would have gone that route, just because of pricing. I really didn't see much difference in the performance when I changed tires, I'm know...

Aurthuritis, I'm running 27 x 11 x 14 on my X1100C front and rear, on aftermarket wheels. I can get you the specs on the wheel as far as offset and backspacing if you would like it. It is a Kanati Mongrel, DOT approved 8 ply. They now offer it in a 10 ply rating, when I bought my set they...

I added these shims to my X1100C, it is a 2014 model. They get added between the rubber bushing and the control arms, on both upper and lower, front and back, for a total of 16 pieces. The illustrated parts list on the Kubota USA site has a lot of information, and shows these shims. It looks...

Aurthuritis, I have the aux hydraulic pump (V5271/V5272) that comes with the Kubota quick connect attachments. It is basically the system that Kubota was using before the K connect. I just have a hydraulic V blade (V5291), but the machine is set up to handle a rotary broom (V5260), the rotary...

I’m working on a project mower, I picked up a New Holland 914A 72” side discharge deck on Craigslist for $300.00. I have the hydraulics on the front to lift the deck and I have what is needed to run the Kubota rotary broom (non K connect model), minus the auxiliary oil cooler, the problem is...

Tom, Great job on the racks, they look like they will serve the purpose well. I had the same problem with ground clearance. I changed to 27" tires and made a 2" lift to get 14" of ground clearance, still have to watch at a few places, but I was constantly dragging before. I have a 2014 model...

I'm no expert on diesel engines, and don't claim to be, so I'm simply asking the questions for someone more knowledgeable to chime in. What would happen if you advanced the fuel timing, turned up the injectors, and turned up the max RPM's without adding the turbo? My unit will blow a puff of...

FullDraw, That is a mighty fine looking rig you have, great job! What was broken in the before picture, was it one of the original aluminum hub housings? Another question, did you make the lift kit yourself, and how much of a lift is that? Again nice work, looks great. Thanks, Pete

It won’t spin the wheels like that, what i did was chain it to my pickup on blacktop and from idle with flooring the accelerator it will spin all four wheels instead of killing the engine, if I do the same thing in high gear it will kill the engine before the turbo spools up. On a sealed...

The pyrometer is on the hot side, the kit comes with a new exhaust manifold, so I just drilled and tapped it for the sensor. The factory manual calls for the max RPM to be between 3070 and 3170 RPM, the instructions say to turn the limit screw out 2.5 turns to give an increase on the RPM of 200...

I installed a turbo kit from turbokits.com on my X1100C. It is a totally different machine to drive now, it will still stall the engine on a hard pull in high gear without the hand throttle being pulled, but in low gear it will spin all four wheels from idle. It climbs without bogging down, or...

Yeehaw48, The dealer told me they thought it was coming from condensation, which I believe is correct. I seldom run through any water, I try to go around the mud holes, it cuts down on the clean up time. I thought I might have gotten water in around the black plug in the top, but afterwards I...

There is a black plastic plug in the top of the bell housing, it is between the exhaust pipe and the motor mount in the top middle of the engine / transmission mount. I pulled mine out and sprayed a water displaced like WD40 in it while the engine was running and let the excess water/residue...

yeehaw48, I have the same machine and was having an identical problem, when below freezing it would not even try to turn over, it happened to me when I was at my cabin in WV without any tools. I tapped on the starter with a piece of re-bar and it started right up, and started the rest of the...