Search results

Can fellow DK owners tell me if the gap between the hood and the cab on your DK has the gap as pictured? I had to troubleshoot a no crank issue on my 4210 with 20 hrs and found water was entering the fuse panel via this gap and freezing the relays during cold weather.

I have a 2017 RTVX1100C with 4000m (6300kms). Recently rotated the tires and found a small bit of play in the rear wheel bearings. Is this normal or with the mileage should I plan on replacing these soon. Also, are they complete hub assemblies or pressed in style bearings? Thanks Jim

Hi Folks, I have to tighten the passenger door handle on my X1100C. Upon looking at the door, I assume I will have to remove the orange panel on the exterior of the door to access it. Is it as simple as it looks to get off?

I recently repurposed the dump bed hydraulic circuit to operate the angle feature on my snow plow. I control the angle from the dump bed lever but it is jumpy and a little too sensitive. Can someone tell me if the system has a built in flow restrictor to adjust the fluid flow rate for this...

What is the most hours/mileage you have seen on a RTV?

Hey guys. I am planning on utilizing the dump circuit on my 1100c to angle my snow plow during the winter months. The plan is to disconnect the lines to the dump cylinder and leave it in place. My question is can I just connect the two lines going to the cylinder together with a joiner so I can...

I am planning on using the Hydraulic circut for the dump bed on my X1100C to power the angle feature of my snow plow. I plan on running these lines from the back where the dump cylinder is loacted to mount on the front bumper area. Has anyone done this? I am wodering about the best route to...

Can someone tell me the sizing of the hydraulic lines going to the dump cylinder on a X1100C?

Can someone tell me why the manual for the 1100C states not to use the hand throttle while driving the vehicle? Also, what is the difference in the optional hand throttle kit that Messicks sells as apposed to the pull up type on the 1100C? Would there be any issue setting the pull throttle to...

We finally had enough snow here on the East Coast to connect the plow to the 1100C and use it. I am so impressed with how much wet heavy snow this machine can push. I have a 6' 8" Meyer Homeplow connected via the upgraded front 2" receiver and it worked out great. The industrial tires seem to...

After a bit of thinking I decided to add a second receiver to the front of the 1100C. I attach a plow system to the machine via the OEM front hitch but found it light to handle the weight of the plow. The new receiver tube is much heavier and is welded to the OEM mount system in multiple places...

Anyone know the bolt size for the 4 bolt holes in the front bumper by the 2" receiver on the 1100C? I tried chasing them with a 7/16 fine thread tap but it seemed sloppy and the 1/2" Fine thread wont start.

Hey guys, anyone here use the Meyer Home plow on their RTV for snow clearing? This particular plow is mounted using the front 2" receiver. What I was wondering is the front receiver on the 1100C heavy enough for this purpose. Thanks

Has anyone figured out or know of a aftermarket setup for a Intermittent wiper setup for the X1100C?

Are there two separate fan belts on the 1100C, one for the alternator-Fan and a separate one for the air conditioning compressor? Also, are there any tips as to adjusting this? Thanks.

I Thought I would give a review of the X1100C I purchased three months ago. It had 40hrs and 400kms on it when I bought it home. So far the machine has performed flawlessly. Runs strong and is quite comfortable for what it is. Below are some of the pros and cons I have observed: Pros: a) Fairly...

My RTV X1100C has two separate oil caps. Whats up with this?

When I bought my 2017 X1100C it came with a Meyer plow system. The plow has its own lift hydraulics pump to lift and lower the blade but has to be manually angled. I was considering re-purposing the bed dump circuit to support an angle cylinder on the plow for the winter months. Would this be...

I am going to install two LED lights to the front of the cab on my 1100C. I am aware that the harness is pre wired to accept these but is there any advice as to how to seal the wires that go through the mounting plate? Never mind, used the search feature and found plenty of info on this...