Once I bought my monster CAT skidsteer bucket... I stopped worrying about bucket wear and tear forever. It will outlive me and the Red Beast by decades. My light-duty bucket is another matter. I've already bought the steel to reinforce the bottom edge... but my lack of welding skill and, apparently, correct welding machinery has put the job on hold until spring.
A lot of the compacts don't have the linkage or the strength of our tractors. Mahindra recommends 15 degrees or less for back dragging. Myself, I have no idea
why anybody would want to back drag dirt with the bucket at a steep angle. If the desired result is to smooth and flatten, then having the bottom of the bucket flat with the ground is what I have found to work the best. Having 24 inches dragging dirt works better that 1/4 ".That would be when you need some penetration in harder stuff to move it back and feather it into a lower area. I will start out at a high angle and modify it while moving. Typically a long pull will include custom modifying the angle back and forth while moving so as to suit whats needed in different parts of the drag. I find it wiil re-rise to hi angle even during a front suspended BD. That shows that pressures under normal conditions do not go above relief. That in itself is a reliefMyself, I have no idea
Just my experience, yours may be different.
Brian,
I am clearing brush with mine. I have been using it all the way down pointing to the ground. But only in low 1st gear.
I too, roll logs with the bucket while I am backing up. One day I may yank a rod out of a cylinder, but that will be one day.
Somehow, I don't think that all you rich members of the ML275 club have an awful lot to worry about.Brian,
You got a point there.
hugs, Brandi
I do not wish to argue the capability of our tractors, that is for sure.
Just my experience, yours may be different.
Similarly, back dragging large rocks and logs away from trees, buildings and other rocks/logs requires a fairly steep angle to be effective. Using the heel of the bucket for such tasks is too dangerous for me. I can't afford to have those things rolling into my front axle.Definitely NOT dirt, but when I'm cleaning out the manure bunker...I'll drop the blade semi-vertical down the backwall of the bunker to drag it away from said wall, so I can then run in and scoop almost every last little bit with the FEL to transfer it to the spreader...
ALso, when I pull snow away from the barn, I use a high vertical, so I get a nice pack and then can run in and scoop up the snow pile...same technique, different color...
Yeah, BBs are great. Often in my case tho, the rear blade will get in the way of maneuvering. The FEL gives more flexibility - down pressure, on the move change in attack angle to dig in, shape or pack down in one pass, ability to reach high and beyond to drag back. Out in the open I would surely employ both, but I am impressed and gratified that the FEL can take firm treatment. I would venture that all FELs that are correctly sized for their tractor will not be harmed by taking advantage of a fairly high BD angle. However, I am basing this on only my use of the loaders on Mahindras and Kubotas. That said, the one on the MH is far the most impressive.
Somehow, I don't think that all you rich members of the ML275 club have an awful lot to worry about.
Dougster
And the problem with that is...???WOW, I didn't know there was a club for us. The local Army reserve just called. They want to use my 6520 & ML275 to lift one of their tanks out of the mud.
hugs, Brandi
I only had a BB and a rotary cutter to use for 3 years before I bought my ML275. I used the BB for all kinds of unmentionable things. But I love the ML275 with it's 84 inch bucket for working dirt smooth and level after having fun with my backhoe. I would use the loader any day over my old BB. There is way more control, unless you have TNT like Brian does. Working brush, the loader bucket is a hands down winner over a BB. It definitely is easier on my neck.Yeah, BBs are great. Often in my case tho, the rear blade will get in the way of maneuvering. The FEL gives more flexibility - down pressure, on the move change in attack angle to dig in, shape or pack down in one pass, ability to reach high and beyond to drag back. Out in the open I would surely employ both, but I am impressed and gratified that the FEL can take firm treatment. I would venture that all FELs that are correctly sized for their tractor will not be harmed by taking advantage of a fairly high BD angle. However, I am basing this on only my use of the loaders on Mahindras and Kubotas. That said, the one on the MH is far the most impressive.
larry
All tractors should have these.
Nice setup! That gives you the ability to change attack angle to make it bite better. Do you take your BH subframe off? I dont see it.All tractors should have these.
MtnView has just said he's going to make sure that everyone here has a TNT...all right...
I'm first in line...
I'm not Bill Gates you know. I think that it should be a more common option though.Sorry... but we already know you've got more money (and toys) than GOD!!!Wait just a garsh darned moment, just because I said that all tractors should have a TNT didn't imply that I was going to pay for all tractors to get them.
Wait just a garsh darned moment, just because I said that all tractors should have a TNT didn't imply that I was going to pay for all tractors to get them.
Brian couldn't afford a backhoe.
Dougster
Unless you have size restrictions or transportation issues, why would you buy one of the removable hoes?
