Recent content by hammerhead

yes.... : )</p> </p> </p>

Good morning fine people.</p> </p> Jamie I did not get your email.... ahh my address did change a year or so ago. Thank you very much for the offer..but I did just fix it. : ) The bumping it.. or pulling on the line while trying to twist the knob did not do anything. I was busy with other...

Hi Jamie:</p> </p> Thanks guys.. I will check it out tomorrow.</p>

Hey Tommy.. I did try bumping the switch.. the motor does run both ways.. but bumping the switch, did not seem to change it the feel at the lever. I can't say I tried it doing both at the same time. I could not reach the lever and the switch at the same time.. I will try that with my wife.</p>...

Hey Brian... [I hope I have remembered that correctly] yes you are correct. when I try to move the lever back to the lock position.. it won't move far enough.. it barely moves at all.</p>

Hi everyone.. it has been some time since I was here.</p> </p> I went to use my winch for the first time in some time. I clicked to freespool, pulled the line out. Hooked it to the tree I was going to move, and then tried to re-engage it, and I could not.....!!</p> </p> As I said it has...

sorry to hi jack.. I have been away for sometime.. and I the forum has changed.. I want to start a new thread..and I can't see a way to do it.</p> </p> hammerhead.</p> </p> I did finally find what I wanted.. and have posted my question in a new thread..</p>

Ok the second side is changed. This one took me 60 to 65 minutes. It felt much much better. Perhaps I am just not understanding the directions but it seems they are telling you to take apart more than you need. hmm now re-reading it, again. On the lower arm.. they want you to loosen the vehicle...

I was going to start a new thread, but that option does not seem to be showing up anywhere right now.</p> </p> I did buy my springs today. I was going to wait, but I guess I was motivated by the others that have changed theirs. Last week I received a spring compression tool for my birthday...

I will probably not change them right away. My time and money are focused on another project at the moment. I will of course post feedback. Where Brian only has a little rub in more extreme conditions I figure the heavy dutier springs will get me back to that "spot:"</p> </p> Of course now I...

Hi Brian:</p> Thanks. I did remember you had some rub, but it seemed in more extreme situations. Mine will do it on flat ground with no load in the bed. Yes I think I will try to replace them myself. I do remember the thread you mentioned where they put in spacers. It sounds like a pretty easy...

Hello Everyone:</p> </p> I have not been able to get on the forum in some time. I am loving my RTV. So far I am happy with all the mods, I have done with the help of the people here on the forum. I do need the heavier duty shocks up front. I did go with the Maxis Bighorn tires like Brian...

<P mce_keep="true"> </P> <P mce_keep="true"></P> Thanks guys. so far it has been basically jump out to toss a branch. The toro I used to let run some because the thing was so bloody coldblooded.. it was always fouling plugs. Brian good point on the chainsaw. The circumstances I was thinking of...

<P mce_keep="true">So Jamie... I thought you were going to buy your wife an RTV also.</P> <P mce_keep="true">There are times when I am doing trail work.. that I need the tractor and the RTV and it's load of tools. So yeah she drives it then. Otherwise I don't think it will be a problem. [:D] if...

<P mce_keep="true">Tommy these trails are not to ride the RTV on. I use them snowshoeing, running and mountain biking. The RTV is just to do the work. making and mantaining these trails[among other things] . To make it more fun for these other "things" I don't want the trails any bigger than...