Search results

Looking at getting a new rtv x1100. How does the k connect system attach to the rtv? Does the system hinder ground clearance? How much of a job is it to remove the entire system in the summer months. Only planning on using it for plowing and snow blowing no summer attachments so I would be...

how are your rear u-joints holing up

Anyone find some aftermarket rear shocks or front struts that will fit the rtv 900?

looking at getting a 3016 but the hoe doesn't offer hyd thumb, is there a kit out there that will fit the Mahindra 3720 hoe. if there is no kit out there will the woods bh80x hoe fit on this tractor?

Anyone have aftermarket u-joint numbers for the front drive shaft.

got a 900 had tjd tracks on it for grooming and could only groom in low at about 2mph. Any one have different tracks that work well on the rtv. any real world experiance?

they were the 397's. Like I said though sure it's operator error

So it's time again to change my rear u-joints!!! Not even a year and way less than 500hrs! I do plow with this rig but come on they should last longer than that. I think I have found the route cause to these u-joint failures. When you let off the throttle the back tires pretty much lock-up and...

I installed a buzzer from a mack trucks warning lights in mine, Very loud had to stuff some paper towel in it to tame it a bit, works good.

I found it was way eaiser to remove the rear springs to get the axle back in. With the springs removed you can line up one side straight with the shaft coming out from the trans, push the slip yoke all the way in then lift the other side and slip the axle in. Worked good for me, I did not even...

doing mine also all you need is a vise and a hammer to get the u-joints out. got the 397 also looked too short when I checked them out the first time but now that there in there only a c-hair short. beats $68 for the bota joints.

Im in the same boat you are, but after a week have had no luck finding the joints. let us know how the 397 joints work out. I went to napa and the 397 was just a bit too short cap to cap compaired to the old one, lock rings were the same though. Anyone see if the 2011 model joints fit hear...

I was thinking of using mirrors off a jeep cj/wrangler

I have big lugs on my rtv with a 6.5' meyer plow on it and have no traction issues. Even plow the lake for skating. Put some weight in the bed and you will have no problems.

So for the sake of argument, could a bigger pump be installed? I know its tight but looks like there is some room there. Or to get more costly and complicated, could a hyd motor be put on driving a bigger pump?

If the problem is the oil getting hot why not get an oil cooler (like the kind that goes in front of the radiator on a car and plum it in.

I found my old post on this here is directions on how to adjust your shifter. Before you get started make sure the cables under the hood connected to the shifter are in the middle of the threads where the jam nuts are and are tight. Also check the ball joints for tightness 1. Put the shifter...

You need to adjust your trans. Creep adjustment and shift cable adjustments. You will find that the shift cables will need to be adjusted often if your machine has low hrs. Once you get some hrs on it the cables will stop stretching as much and time between adjustments will get longer. Do a...

Heres a crude drawing but you get the idea. The lift was hooked into a winch mount I made (kind of like a muti mount for the 4wheelers) in the stock location where the winch mounts. It could be made to fit where the front trailer hitch goes. The lift fit very close to the brush guard.

I made a lift when I had the American eagle plow for my rtv 900. It used a pulley with the winch and would lift the plow straight up and almost hit the front brush guard. Wish I took pics. It would lift the plow so high that the face of the blade was parallel to the ground. The american...