Search results

Hello, apparently a discontinued part by kubota. If anyone has one used i be happy to buy it. Pressure line for power steering. From the steering column to the engine pump. Part # k7561-41530 I have done my homework. Used online I can only find being sold altogether with steering motor for 400$...

Hello my friends, while out putting hours on my recent 04 kubota 900 dieasel an making sure its up to par for my mountain an cabin tasks ,I wanted to (without gauges) test my hydrolics out as far as the drive train. So I put the nose of the machine up against a heavy truck bumper, put my rtv in...

Ok.here are the photos of the tailgate i made.also the photo of the kawasaki mule bed,which bolts right onto the kubota.im using the mule bed ,which had no gate,my kubota bed was junk.but... The sides were ok.so the sides are 3 inches or a bit more shorter than the gate width. So I cut one...

Thank you to everyone here that helped me through this process of bringing my nightmare to a dream literally.I had many questions an everyone here was so helpful an nice,(everyone) Thank you all! I have that nervousness still as I always do with any new to me vehicle until I get some hours on it...

Hello again all,I know everyone loves pics so below a couple on my floor an fender wells I made.The floor i made out of alluminum so no more issues,an the wheel wells are galvanized steel.then zinc primed,an then sprayed 4 coats of truck bed liner on them.the chasis I ended up making with box...

Its all dovetail an post an beam.did it all by myself just got it dried in finally, finished floor soon,an this is my full time permanent home,no grid at all.its on a mountain I purchased for my retirement.happy to answer any questions.

Hello everyone,I'm to the point of assembly an when I go to put the plastic nose panel,that has the headlights an all in one piece,(pics below) I only see 2 bolt holes on each side that are in the cab holding this entire piece on? Nothing at all in front or outside at all. Is there something I'm...

Ok,my frame is done finally! I made a template for the floor wheel wells,was pretty easy actually,I was able to do it with only one seam! Two sections.i used my flatbed truck as a bender lol.put the metal between my 2x8's on my truck flatbed,an boom! Results in my photos below,an on my YouTube...

I apoligize already,but being green to these rtv's, how hard should these be to push on flat level ground in neutral? I had a dam hard time even moving mine,had to tow it.im thinking.if its not supposed to be like that, I need to check brakes hanging up mayb? Any thoughts? 04 rtv 900.

No need to be perfect just useable! I can't afford a new one for 600$ an searched everywhere for used for a reasonable price anyway.

Ok.the worst passenger side is finally complete! The front tube at strut is complete on drivers side. Now I need to start the frame on drivers side tommorow! Before an after pics attached!

Anyone happen to have a rear tailgate for a 04 rtv 900? Does not need to be pretty or shiney! Just atleast able to be used. I just do not have 600$ for one.i can make something if needed.im just trying to find one first halfway decent.i have searched all other places already before asking here...

Hello again,I'm at a stopping point briefly, I have removed the front gear cover on my 04 D902 engine to replace the cam an use a new cover.now that im ready to re assemble it,I see in the wsm to make sure you use a gasket sealor on both sides of the gasket,which I was going to use a little...

So now I'm unsure of my direction, 2 engines I brand new engine literally but sat an got some water in a cylinder,unfortunately it got pitted. Its hard to see if I can just buy a set of sleeves,an put them in an re ring it an be back to perfect or does it have to be bored by a machine shop? If...

Ok,after from being down an spset,spent, the score of my life,I'm not sure what's next.as I went to get a used head for my 04 rtv 900,I found a honey hole of engines an parts from a old friend, he gave me an entire new engine for the price of a head!!! So as I'm in the garage adding what I need...

Well after selling my perfect jeep so I could buy a rtv to help me work,I spent all I had on this supposed to be "runs like a champ" an "frame is fine" 04 kubota rtv 900 that was also sold to me as a 2011 come to find out its none of the above.im retired an live on my check .after finding all...

I have a brand new set of tires for my rtv, Front tire Size is 26 /8/12 Rim size is stock 12x8.5 I just mounted them but before I inflate them it looks like I may be using the old either trick or have to get a rim clamp its going to take a bit with the space... Is this normal or ok? I really...

I'm located in Rhode island/ct line can travel a bit or pay shipping. Thank you.just trying to save some money from purchasing new or god forbid dealoe price😑 Thank you, Derek

Please help me to get rolling,I'm in need of atleast 1 but will buy 2 or 4 Rims ,the old 5 lug pattern 12x8.5 please if your local or you ship on my dime. Can pay whatever your preference is. I didn't think it be hard to find stock ones.apparently it is...I don't like dealing with unfamiliar...

First off,happy new years to everyone,an hopefully a much better one for everyone,an myself. I have just purchased a 2004 rtv 900 diesel an while I have a ways to go before I can even get it to be usable, I'm curious since I have this machine completely stripped down,rebuilding the lower front...