No Start CK2510

K

Koski J

New member
Hello,
My CK2510 did not start today after being parked for several days. Let me provide some background. Tractor has 107 hrs on it.

One day the tractor didn't start. I found the battery dead. (I left the key on "ACCY" I removed the battery, charged it and performed a load test. Battery checks good. Reinstalled the battery and the tractor started. Next, I checked the charging system. Alternator not charging. Just showed battery volts. Found fan belt completely worn out and slipping. Replaced fan belt with one from NAPA. Start the tractor and still not charging. Removed alternator (107hrs) and stopped by an electrical shop. They bench tested the alternator and it checked ok. Brushes good. Output 14.0 Volts. Reinstalled alternator and belt. Started tractor. No alt light on. Drove tractor to my shop and parked it.

8/28: Went to start tractor. No start. Tested battery 13.1 volts. There is a click when key is turned to "start". (Relay?) Removed starter and bench tested. Starter ok. reinstalled. Tried to find a wiring diagram online with no luck. I know there are several safety switches that need to be engaged before the engine starts. One is the seat switch and one is the transmission/gear switch. The trans needs to be in Neutral. Maybe a parking break switch too.

Tomorrow, I'll check for power/continuity in the safety switches. Does this tractor have a starter solenoid? Is there something I missed? Anyone else have this or had this no start issue? Any and all advice is gratefully appreciated. I'll post finding when the job is completed.
 
Update: I went back out to troubleshoot. I didn't find any chaffed or broken wires or connectors. I did get the tractor to start by wiggling the H/N/L shifter. I placed the shifter in Neutral and the tractor started. I turned it off. Reinstalled a cover panel. Jumped back on to start and again "No start". I now believe that the problem lies with the shifter lever and it's position. There's a small electrical box next to the shifter, See photos. Would this be a neutral safety switch? The lever to the right side of the box is the range selector. Back to research.
 

Attachments

  • 20250828_151553.jpg
    20250828_151553.jpg
    1.6 MB · Views: 2
  • 20250828_151624.jpg
    20250828_151624.jpg
    897.4 KB · Views: 1
  • 20250828_151611.jpg
    20250828_151611.jpg
    1.1 MB · Views: 2
Is there a way to update my messages without completing a reply? Anyway, I have continued to search and the photos I posted is not the neutral safety switch, I have no idea what this box does.
 
The box says "Safety Control Unit". Not sure exactly what that means for your tractor.
When my tractor encounters the no-start condition you've mentioned, it's normally a bad battery connection or the battery cables themselves.
Try bypassing the battery cables by routing jumper cables in parallel to the battery cables.
 
Thanks BCzoom for the info. I'll check it out and post the findings. Note: I did check the neutral safety switch for the gear lever, continuity is good.
 
BCZoom: tried what you suggested and that didn't work. I went back to square one and started again. Fast forward I have no voltage to the starter relay when the key is switched to start.
Here's what I've checked:
Battery good at 13.3 volts.
Fuses check good.
Relays (2) have voltage in and I'm assuming out since the continuity check was good.
Voltage to the starter from battery +cable.
Voltage into and out of the park brake switch.
Voltage into and out of the seat switch.
Voltage into and out of the neutral safety switch.
Inspected the wiring, find no chaffing or broken wires.
Could the ignition switch be the problem?
I'm about to the end of my knowledge.
 
Do you have a jumper box? If so, connect it to the starter solenoid and a good ground and try to start it.
Check any/all connectors to the starter relay.
 
Update: Success! Along with all the other switches on this tractor, I forgot to check the PTO!
Found the PTO switch was in the wrong position. I feel like a dutz. I should have known, but I over looked it.
Now to put the tractor panels and hood, back on. Thanks for all your help.
 
Don't feel bad. It happened to me once. Darn winter boot or snow pants moved the lever when I got on.
Good news is you've given your tractor a good preventative maintenance electrical inspection. :)
 
You must log in or register to reply here.
Top