Recent content by JWHAYS

<P mce_keep="true">Yeah, I kinda think that's what happened. Like I said, I have it lock-wired to the frame. When I need it, I'll just cut the wire and use the support.</P> <P mce_keep="true">...John</P> <P mce_keep="true">Oak Hills, CA...in the rainshadow of the San Gabriel Mountains</P> <P...

<P mce_keep="true">Yes, that's exactly what it's used for.</P> <P mce_keep="true">I don't want to beat a dead horse here, but with the bed down I don't see how this support can come off the rail. There is also a braided stainless steel cable attached to the support, the other end of which is...

<P mce_keep="true">I have never used the safety support; in fact, I didn't even know it was there. I had the vehicle in for service a few months ago. It would be tough to prove someone else put it back incorrectly.</P> <P mce_keep="true">...John</P>

<P mce_keep="true">Yes, and it is stowed on the frame behind the driver's side. It's beyong me how it came loose. I'll see if I can take a picture of it. I'm also going to take the machine to the dealer tomorrow.</P> <P mce_keep="true">...John</P> <P mce_keep="true"></P>

<P mce_keep="true">The safety support on my RTV900 came off the frame and ended up getting wedged between the frame and the left rear tire. I was going down a bumpy desert road at the time and smelled burning rubber. I stopped the vehicle and discovered the problem. The support abraded the...

My winch rocker is mounted below the dash. The RTV900 came with a winch.</P> BTW, both the turn switch and headlight switch are to the left of the hazard switch. I may have made it sound confusing in my previous post. It confused me when I read it!! :)</P> ...John</P>

The turn signal switch is also on the dash, to the left of the headlight switch and the hazard switch. The steering wheel did not have to be removed, at least on the 900.</P> ...John</P> Oak Hills, CA</P>

Re: BEDLINER FOR RTV 900 Mine came with a bed liner and am very happy with it.</P> </P> ...john</P>

well, I did a little checking and found two blown fuses. Replaced same and all works well.</P> ...John</P>

Installed the kit and the only lights working are the brake lights. No turn signals, no hazard lights, not even the headlights now.</P> In the directions, a 'panel switch plug' is to be removed. Anybody know what this might be?</P> Thanks in advance...</P> ...John</P>

Hmmm...where in the instructions does it say to remove the steering wheel?</P> And you did the installation in about one hour? Hayfarmer 'you da man'!!</P> </P> ....john</P>

David, just picked up the kit and am looking thru the instruction manual. It looks clear and to the point. My dealer asked me if I was going to install it and I said yes. They were gracious enough to offer help if I needed it. They're a good group at Apex Rentals in Hesperia.</P> ...John</P>...

Mark, welcome to RTV world!</P> I'm a newbie, but have put the machine thru some pretty incredible situations. I live out in the high desert where we have soft sand and steep hills. It's an amazing machine!</P> I've found the folks out here to be very helpful and friendly. Welcome...

Andrew- we will be hitting up the Pizzeria Uno for sure. Let me know where those other places are please. </P> ...John</P> Oak Hills, CA</P> exa4mech@yahoo.com</P> </P>

Andrew- I had to laugh about shotguns not being sawed off! I was born and raised on the South Side. Left in 1965 (20 years old) and went in the Navy. My wife and I are going to Chicago this Saturday, for a few days.</P> ...John</P> Oak Hills, CA</P>